Flame Ionization Detector (FID) Based
Hydrocarbon Analyzers / Monitors
Environmental Instrumentation
Manufacture, Sales, Service & Rent
VIG Industries, Inc.
4051 East La Palma, Suite C
Anaheim, California 92807-1751
Toll Free in the US: (800) 862 - 7844
Main: (714) 632 - 8200
Fax: (714) 632 - 8201
Email: Service@vigindustries.com

Home - Welcome
FID Hydrocarbon Analyzers
    Spot Heated Analyzers
     Model 10    Model 10/2
    Oven Heated Analyzers
     Model 20    Model 20/2
     Model 200  Model 200/1
     Model 210  Model 210/1
FID Hydrocarbon Analyzers NDIR Analyzers
     Model 300  Model 300/2

CEM Systems -
    Power Generation
    Abatement Systems
    Process Control
    Spray Booth
    Environmental Compliances

 Zero Air Generators
Dilution Systems
Heated Multipoint Sequencers
Temperature Controllers
Liquid / Gas Separators
Chart Recorders
Data Loggers
 Components
Literature Request
News and Announcements
Rentals, Sales, and Service
Clients List / References
Sitemap and Search
Environment / Industry Links
 Contact Us

  

Model 300/2 Dual Gas Non-Dispersive Infrared NDIR Analyzer (No longer available)

VIG Model 300/2 Dual Non-Dispersive Infrared Gas NDIR Analyzer

The VIG Industries, Inc. Model 300/2 is designed to measure a two gasses (or three with oxygen option). The Model 300/2 optical bench consists of the IR source, sample cell, and patent pending detector. The source control circuit provides a controlled current square wave to the infrared source.

No mechanical chopper is used so there are no moving parts in the Model 300/2 optical bench which require adjustment or can wear out. Infrared energy from the source passes through the sample where energy at specific wavelengths is absorbed by the sample. The closed sample path eliminates interfering absorption from ambient air. The energy not absorbed in the sample cell reaches the detector which is sensitive to the wavelengths attenuated by the gas of interest.

The patent pending Model 300/2 detector consists of two chambers in optical series with a very sensitive transducer to measure the relative energy absorbed by each chamber. The primary difference between the Model 300/2 detector and other NDIR detectors is that these two signals from the primary and secondary chamber are balanced. The balancing process greatly improves the sensitivity and selectivity for the gas of interest.

The vacuum fluorescent display continually monitors the concentration of the gas of interest in the selected units, as well as the zero and span values during calibration. The bottom line displays chart recorder range, linear or non-linear mode, and response time. Any error or alarm condition will alternate with this information until acknowledged by the operator. Operating parameters are established by way of the four buttons on the Model 300/2 keyboard.

The setup button is used to define settings such as calibration gas concentration, sample cell flush time, automatic calibration intervals, chart recorder ranges (1-4), and high and low level alarms. The mode button is used to select active chart recorder range, response time, linear and non-linear units, activate the audible alarm, adjust display brightness, and initiate manual zero and span calibrations. The arrow are used to make changes in values or selection of desired parameters in the setup and mode functions. In the event of a power failure, battery backup retains all settings.

Applications

  • Process control

  • Stack gas monitoring

  • Continuous emission monitoring

  • Combustion efficiency

  • Environmental gas analysis

  • Heat treating

  • Natural gas plants

  • Utility plants

  • Flue gas analysis

  • Coke oven analysis

  • Carburization Processes

  • Monitoring of: boilers, incinerators, furnaces

  • Vehicle Emissions

Features

  • No range switching or over range conditions

  • Digital signal permits microprocessor linearization for increased accuracy

  • Optional oxygen channel

  • Optional NEMA rated enclosures

  • Measurement of one of the following selected gasses:

    • Methane

    • Propane

    • CO

    • CO2

    • NO2

    • SO2

    • NOX

Standard Specifications

 
Analysis Method NDIR Single Beam
Gas Measured User Selectable
Measuring Range User Selectable
Resolution 0.1% of Full Scale
Repeatability 0.1% of Full Scale
Noise 0.1% of Full Scale
Drift 0.1% of Full Scale
Response Time at 1, 10 or 100
Display Vacuum Fluorescent, 2 Lines of 16 Alphanumeric Characters
Alarms High & Low Limit, User Selectable
Analog Output Selectable 0-1, 5, 10Volts, Optional Isolated 4-20mA Loop
Analog Ranges 4, Each With Adjustable Full Scale. Selectable Auto Range
Front Panel Four Button Interface, Using Display Menus
Voltage 0-1, 5, 10Volts, Selectable
AC Output Isolated Triac Control for Zero & Upscale Gas Values.
Rated Maximum Load: 0.6Amp, 240VAC

Operating Requirements

 
Power 115/220Vac, 50/60Hz
Power Consumption 200Watts
Sample Flow .2 to 2.0 Liters/Minute
Sample Temperature -10 to +50 Degrees C.
Dust Sample Should be Dust Free
Moisture Non-Condensing
(Dew Point Below Outlet Temp. of Analyzer)
Pressure Inlet Gas not to Exceed 5PSIG
Exhaust Gas Non-Restrictive Outlet Aperture/Hoses
Zero Gas Typically Nitrogen
Upscale Calibration Gas Gas of Interest in Nitrogen
Warm Up Time Useable in 30 Minutes. Optimum Operation in 2 Hours
Ambient Conditions Operating -10 to 50 Degrees C.
Storage -10 to 80 Degrees C.
Dimensions 22"L x 18"W x 5.25"H
Weight 22 LBS

Warranty

All instruments sold by VIG Industries, Inc., are warranted for a period of one (1) year from the date of purchase, against defects in materials and workmanship. VIG warrants that the product supplied conforms to the specifications assigned thereto. There is no other warranty either implied or expressed. Seller liability is limited specifically to the cost or assigned value of the items sold.


 


 

Copyright © 1998-2004
Webmaster
Revised Nov. 4, 2009
VIG Industries, Inc.
 

 

To The Top, Please...